 |
|
|
 |
CYPRES - EXPERT ONE PIN CONTAINER
|
 |
|
|
|
Réf : I1501
900 Euros H.T.
|
|
How CYPRES works:
Cypres meets all needs and wishes of today’s skydivers. Once it is installed, you can’t hear it, you can’t feel it and you can’t see it. The operation is quite simple: Just switch it on in the morning prior to the first jump, then forget about it. Even jumps onto another elevation are no problem: Simply hold your finger on the button until the required elevation difference is displayed. Every time Cypres is switched on, it will calibrate to ground elevation by measuring the air pressure several times in a short period of time and taking the average value as the value for ground level. This is happening during the integrated self-test which also checks the battery, the entire internal electronics, etc. If this check is successful, Cypres will go into function-otherwise it will shut itself down. While it is in use it will constantly check the air pressure on the ground and, if necessary, adjust to changing weather. This always provides an accurate calibration which is the basis for Cypres to recognize the activation circumstances. The factory-programmed microprocessor of Cypres is capable of real-time calculations of the jumper’s altitude and rate of descent on the basis of barometric pressure. By monitoring this data, certain criteria are generated from which conclusions are drawn. Should the conclusion be that the jumper is in a dangerous situation (i.e. still in freefall at a low altitude) the processing unit triggers the release unit to open the reserve container. The release unit for the reserve container is completely independent of the rig’s system, because it does not pull the ripcord pin out of the closing loop but actually cuts the loop inside the reserve container to release the pilot chute. This method is exclusive to Cypres.
Expert Cypres
Whatever you can think of under the canopy, like stalls, spiral turns, down planes, hookturns with the smallest canopies, as well as any CRW, Expert Cypres won’t interfere with any activities while skydiving. It activates when it detects a rate of descent higher than 78mph (35m/sec) at an altitude of approx. 750ft above ground level (AGL).
|
|
|
|
|
 |
 |
|
|
|
|
|
REPLACEMENT BATTERY FOR CYPRES
|
|
|
|
|
Réf : I1525
75 Euros H.T.
|
|
|
The Cypres is powered by a battery power pack assembly that can be used for a maximum of two years, 500 jumps, or until the self-test (via code 8998 or code 8999) that the battery needs to be replaced - whichever occurs first. In most cases, this is two years. The two year period starts when the battery pack is plugged into the Cypres. Spare battery packs may be stored in proper conditions for up to three years prior to installation.
|
|
|
|
|
|
|
|
|
|
|
|
PACKERS KIT FOR CYPRES
|
|
|
|
|
Réf : I1524N
30 Euros H.T.
|
|
This is a package of replacement parts that a rigger will need from time to time when packing rigs with Cypres installations. The Cypres Packers Kit also contains everything necessary to equip rigs with Cypres reserve container closing loop systems. The Cypres loop material increases the safety of its user regardless if a Cypres is in the rig or not. It does this by improving the opening performance of the reserve container, by reducing the necessary pull force on the ripcord up to 50%, and by reducing the risk of loop tearing. The Cypres Packers Checklist also allows for checking every Cypres installation for its correctness.
Contents: 1 spool of Cypres loop material (50 yds), 1 finger trapping needle, 1 container of silicone gel, 1 siliconized cloth, 1 temporary pin, 5 loop discs, 1 Cypres user’s guide, and 1 Cypres packers checklist.
|
|
|
|
|
|
|
|
|
|
|
|
CYPRES REPLACEMENT CUTTER
|
|
|
|
|
Réf : I1527
105 Euros H.T.
|
|
|
Replacement cutter for one pin Cypres. The Cypres has a unique method of opening the reserve container, using a device that cuts the reserve container closing loop. It is completely independent from the normal reserve container opening system. While a jumper uses the reserve ripcord handle to pull the the reserve pin out of the eye of the closing loop, the Cypres uses a cutter which cuts the closing loop itself. This autonomous design has saved the lives of skydivers with damaged reserve pins. After an activation, a replacement cutter can easily be plugged in.
|
|
|
|
|
|
|
|
|
|
|
|
CYPRES TEMPORARY PACKING PIN
|
|
|
|
|
Réf : S7425
3 Euros H.T.
|
|
Needed for packing Cypres equipped rigs where there is a small loop. Original equipment, comes with warning flag installed.
|
|
|
|
|
|
|
|
|
|
|
|
CYPRES LOOP MATERIAL - 50 METER SPOOL
|
|
|
|
|
Réf : I1535
20 Euros H.T.
|
|
|
50 meter spool of Cypres reserve closing loop material. The Cypres loop material increases the safety of its user regardless if a Cypres is in the rig or not. It does this by improving the opening performance of the reserve container, by reducing the necessary pull force on the ripcord up to 50%, and by reducing the risk of loop tearing.
|
|
|
|
|
|
|
|
|
|
|
Voir le panier